企鹅粮油机械在线教大家怎么使用榨油机技巧

         榨油机械：企鹅粮油机械在线教大家怎么使用榨油机技巧
         榨油机正常运转后，含油量高的油料出油大多集中在条排和前组圆排处。条排处的出油约占总出油量的60%，前组圆排处约占30%;而末端排出油则很少，成滴不成线，油色很清。反复榨二三次即可将菜籽或黄豆的油榨尽，在这期间可将含油较多的油渣均匀地掺人料胚中压榨，下料时要保持均匀，切忌忽多忽少，否则将影响榨油机的寿命和出油率。
Press the normal operation, high oil content of fuel oil are mostly concentrated in a row and the front row at the circle group. A row of oil accounts for about 60% of the amount of oil, before the group round discharges accounted for about 30%; and the end of the discharge oil is very few, drop a line, color is very clear. Repeatedly pressed three times can will rapeseed or soy oil press, in this period can be more oily sludge uniformly mixed in the blank press, feeding to maintain uniform, avoid by all means is suddenly more and less, otherwise it will affect the press of life and oil yield.
        满足预处理工序要求料胚入榨前，要经过预处理工序，预处理质量将直接影响榨油机正常工作和出油率。
Meet the pretreatment process of billet requirements before pressing, must after pretreatment, pretreatment quality will directly affect the normal work of the press and oil yield.
         如出饼疏松无力，或出饼不成形，色泽较深，用手一捏即成碎块，这说明胚料加水太少;如出饼发软，成大片状，或出油泡沫增多，则说明加水太多。正常情况下，圆排之间不出渣或很少出渣，在条排处出渣，如出渣呈细片状说明水分多，出粉渣则说明水分少。此外，以出油位置变化可看出入榨水分是否合适，当入榨水分过高或过低时，出油位置均向后移。
Such as cake loosening weakness, or a cake not forming, deep color, hand pinch into fragments, indicating that blank water too little; such as cake weak, into a large shape, or out of the oil bubble increased, too much water. Under normal circumstances, circle line between no residue or rarely slag, in a row at the slag, such as slag was flakes that much water, slag powder that less water. In addition, in order to change the location of the oil can see whether the right of the entrance and exit, when the water is too high or too low, the oil position are backward.
      运转过程中要经常检查榨油机的出饼情况，并控制胚料的水分既不过高也不过低。正常的出饼应呈片状，靠榨螺轴一面光滑，另一面有很多毛纹。
In the process of operation should always check out the cake case press machine, and control the blank water is neither too high nor too low. The normal out of the cake should be a piece of cake, by pressing the screw axis is smooth, on the other side, there are a lot of hair lines.
     进入加工厂的油料含有一些的杂质(泥沙、石子、铁屑等)，若不仔细清选，会加速榨油机内部机件的磨损，降低出油率，甚至造成故障和事故。与其配套的设备有：清理筛、去石机、磁选机等。对于带壳的油料，应剥壳后再压榨，这样可以提高生产能力和出油率。
Into the processing plant oil containing impurities (sand, gravel, iron, etc.), if not carefully cleaning, will accelerate the press to the internal parts wear, reduce the rate of oil, and even cause accidents and malfunction. Matching equipment: cleaning sieve machine, magnetic separator, etc.. For shell oil, and should be re pressing, this can improve the production capacity and oil yield.
    与其配套的设备有：剥壳机、分离筛、分离机等。某些油脂可以整料入榨，但经过破碎、轧胚后再压榨，可明显提高出油率。与其配套的设备有：破碎机、轧胚机等。
Matching equipment: peeling machine, separating sieve, separator etc.. Some of the oil can monolith pressing, but after crushing, flaking after pressing, can significantly improve the oil yield. And its supporting equipment: crusher, rolling machine, etc..
郑州企鹅将秉承着可靠的设计，制造，安装经济，有质量保证的。榨油行客户世界各地，如果您有任何问题，请与我们联系.0371-86661079
下面是我们为大家推荐的浸出设备：
             浸出设备: http://www.oilqie.com/jcsb/92.html
             成套浸出设备: http://www.oilqie.com/jcsb/91.html
             冷凝系统: http://www.oilqie.com/jcsb/90.html